我的博客列表

2015年12月15日星期二

Tungsten Copper EFP Liner

Tungsten copper EFP liner having a higher density and strength, mainly used in the current foreign Shaped drug type cast. Studies have shown that three high-caliber bomb under conditions comparable depth of its armor Cu Liner material increased by about 30%. Therefore, W-Cu composite explosive forming Liner munitions will also have great potential.

Scientists have studied the preparation and formability 30W-Cu EFP liners of. Ordinary tungsten powder, copper powder and ultrafine preparing two tungsten-copper composite powders of different bars, and then test the performance forged bars, final selection of material for producing a forged good performance EFP liners. Studies have shown that: the ordinary tungsten powder, copper powder prepared material has good pressure processing performance; prepared density 30W-Cu EFP liners materials 98.2% of theoretical density, tensile strength after annealing material reaches 315 MPa, elongation rate was 15.3%.

By experiment under the same sintering conditions, ultrafine tungsten-copper composite powders prepared density material is superior to the use of the material prepared in the ordinary powder, but the material of ordinary powder preparation has better pressure processing performance.
It can significantly increase the density of tungsten-copper sintered materials by forging, annealing after forging 30W-Cu EFP Liner material density up to 98.2% of the theoretical density. After the heat treatment the tensile strength of the material reaches 315 MPa, elongation rate was 15.3%. 

2015年11月16日星期一

Tungsten Copper Linner

Tungsten copper linner combination of high density and ductility of tungsten copper, compared to copper liners have higher power and armor shaped effect. The disadvantage is that tungsten and copper can not dissolve each other, and because of the density difference between the two large, easy to form when gravity segregation caused by compression molding liners inhomogeneous density distribution.
Tungsten copper alloy as an ideal material for liners, but there is more in the preparation process issue, tungsten copper alloy bonding strength is poor, molding material difficulties; its wear deep fried sensitive to high variability, it should only lower Fried use under high conditions.

You can improve the disadvantage of tungsten copper linner by the following:

1, a conventional tungsten copper alloy density difference obtained by the method, the uneven density distribution, a more effective method for mixing powder or the preparation of molding can be used, including isostatic pressing and the like.
2, changing the sintering temperature and obtain better bonding strength.
3, on the layered liners do question whether it will result in poor stability problems.
4, if the density and bond strength can be improved, and then use the company's strengths, the material is rolled into sheets, tungsten copper alloy Liner material prepared by spinning, stamping or forging methods.

90W10Cu Tungsten Copper Sheet

90W10Cu tungsten copper sheet mainly used to suppress the high-speed technology to prepare, and then in 1400 ℃ high temperature hydrogen furnace infiltrated get 90W-10Cu composite. Research repression affect the quality of the pyrometer compacts green density and microstructure of. The results of surface, with the suppression of the temperature rise, the compact density, high-speed suppression obtained at 950 ℃ relative density greater than 80.65% of W skeleton dense tungsten particles connection, distribution, pore connectivity is good. Compacts increases quality, due to the applied energy density is reduced, leading to the green density decreases. By twice the height of repression, the green density further increase; the relative density of 99.5% 90W10Cu materials, thermal conductivity 175W / (mK), tungsten copper alloy 90W10Cu indicators have reached the requirements of the appropriate heat sink material.

90W10Cu Tungsten Copper Sheet Properties Conclusion

1, At 950 ℃ high speed pressing attainable relative density greater than 80.65% of W skeleton, by infiltration get 90W10Cu composites.
2, At room temperature, 600 ℃, 950 ℃ for high-speed tungsten preform pressing, pressing as the temperature rises, the green density increases.
3, High velocity compaction,  powder mass increases, due to the ability of additional density decreases, resulting green density decreases. With the increase in the number of high-speed pressing, green density is improved.
4, Using high-speed pressing technology combined with infiltration of 90W-10Cu preparation material and the thermal expansion coefficient and other indicators have reached the requirements of the appropriate heat sink material.

2015年10月19日星期一

What is Tungsten Copper Block

Our tungsten copper block looks like a gold block, it is so beautiful. And the longest length and width we are able to provide is 500mm, and the most thickness is 8mm. We are able to provide the composition with 93W, this material always used on the military industry. The properties of these material is also higher than common materials, so if you have any special required on the properties, you could do not hesitate to contact us.
The following is the block we have finished for your reference:


If you have any other special required on the size or properties, you could contact us by sales@chinatungsten.com, and we could reply you as soon as possible.

Sincerely hope could cooperate with you in the near feature.

How to Make Tungsten Copper

The method of tungsten copper machining is mainly divided into two categories: infiltration and direct sintering method. In recent years, due to the rapid development of nanotechnology, directly obtained by sintering a great development.The melting point of tungsten, copper vary greatly higher than the boiling point of the copper melting point of tungsten and tungsten copper immiscible, the general method of smelting is difficult to produce tungsten copper alloy, the only powder metallurgy to make tungsten copper composites manufacturing to become a reality.

Tungsten copper machining include the following methods:
Infiltration Method
High Temperature Sintered Tungsten Copper Alloy
Mixed Powder Sintered Copper Infiltration Method
Direct Sintering Method

Our general method is infiltration, the infiltrated divided into high temperature sintered tungsten skeleton copper infiltration and low-temperature sintering mixed powder copper infiltration two.

The following is the picture about our tungsten copper maching method:


2015年9月14日星期一

Tungsten Copper Material MSDS

Material Safety Data Sheet (MSDS) is a table about data regarding the properties of a particular substance, which may concern instructions for the safe use and potential hazards associated with a particular material or product. Therefore, MSDS is important and necessary for chemicals users.


Of course, the tungsten copper we provided also have MSDS, and more about tungsten copper’s MSDS please feel free to visit: http://www.tungsten-copper.com/MSDS-of-tungsten-copper.pdf
At the same time, following is the picture about our tungsten copper products, which are suitable for the MSDS:

The sheet aims to offer workers and emergency personnel with procedures for handling or working in a safe way, and includes information such as physical data (melting point, boiling point, flash point, hardness, ultimate tensile strength, density, etc.), toxicity, health effects, first aid, reactivity, storage, disposal, protective equipment, and spill handling procedures. The exact format for MSDS can vary from countries to countries by respective national requirement.

Tungsten Copper EDM Electrode

Tungsten copper EDM electrode is a powder metal product designed to combine the best EDM properties of tungsten and copper. Tungsten copper combines the high electrical conductivity of copper with the high melting point of tungsten. The combination of these two metals creates an electrode material with very good wear properties.

The manufacturing of Copper Tungsten Electrodes is telling about a combination of two metals: copper and tungsten. So this is a product is caring the properties of both the metals. Copper tungsten rod is highly heat resistant and conductive. 10 – 50% copper is incorporated according to the demand of usability.

Features of Copper Tungsten EDM Electrodes:
Thermal and electrical conductivity up to a high limit
Available in both finished and semi finished shape
Our product range also comprises of tungsten copper bar, tungsten copper blocks and other tungsten copper products. And if you have any other inquiries about our products, please do not hesitate to contact us with: sales@chinatungsten.com